SEARCH CONTACT US SUPPORT SERVICES PRODUCTS STORE
United States    
COMPAQ STORE | PRODUCTS | SERVICES | SUPPORT | CONTACT US | SEARCH
gears
compaq support options
support home
software & drivers
ask Compaq
reference library
support forum
frequently asked questions
support tools
warranty information
service centers
contact support
product resources
parts for your system
give us feedback
associated links
.
} what's new
.
} contract access
.
} browse patch tree
.
} search patches
.
} join mailing list
.
} feedback
.
patches by topic
.
} DOS
.
} OpenVMS
.
} Security
.
} Tru64 Unix
.
} Ultrix 32
.
} Windows
.
} Windows NT
.
connection tools
.
} nameserver lookup
.
} traceroute
.
} ping
OpenVMS VMS73_DRIVER-V0200 Alpha V7.3 Drivers ECO Summary

TITLE: OpenVMS VMS73_DRIVER-V0200 Alpha V7.3 Drivers ECO Summary New Kit Date: 08-JAN-2002 Modification Date: Not Applicable Modification Type: New Kit NOTE: An OpenVMS saveset or PCSI installation file is stored on the Internet in a self-expanding compressed file. For OpenVMS savesets, the name of the compressed saveset file will be kit_name.a-dcx_vaxexe for OpenVMS VAX or kit_name.a-dcx_axpexe for OpenVMS Alpha. Once the OpenVMS saveset is copied to your system, expand the compressed saveset by typing RUN kitname.dcx_vaxexe or kitname.dcx_alpexe. For PCSI files, once the PCSI file is copied to your system, rename the PCSI file to kitname.pcsi-dcx_axpexe, then it can be expanded by typing RUN kitname.pcsi-dcx_axpexe. The resultant file will be the PCSI installation file which can be used to install the ECO. Copyright (c) Compaq Computer Corporation 2002. All rights reserved. OP/SYS: OpenVMS Alpha COMPONENT: Drivers SOURCE: Compaq Computer Corporation ECO INFORMATION: ECO Kit Name: VMS73_DRIVER-V0200 DEC-AXPVMS-VMS73_DRIVER-V0200--4.PCSI ECO Kits Superseded by This ECO Kit: None ECO Kit Approximate Size: 160 Blocks Kit Applies To: OpenVMS Alpha V7.3 System/Cluster Reboot Necessary: Yes Rolling Re-boot Supported: Yes Installation Rating: INSTALL_3 3 - To be installed by customers experiencing the problems corrected. Kit Dependencies: The following remedial kit(s), or later, must be installed BEFORE installation of this, or any required kit: VMS73_UPDATE-V0100 In order to receive all the corrections listed in this kit, the following remedial kits, or later, should also be installed: None ECO KIT SUMMARY: An ECO kit exists for drivers on OpenVMS Alpha V7.3. This kit addresses the following problems: PROBLEMS ADDRESSED IN VMS73_DRIVER-V0200 KIT: o When the CD-ROM is booted on an ES40, the following error message is returned after the initial boot messages: %SYSBOOT-I-GCTMINOR, GCT used with minor revision mismatch expected 00000005.00000001 - seen: 00000005.00000002 %SYSBOOT-F-LDFAIL,unable to load SYS$BASE_IMAGE.EXE,status=00000054 halted CPU = 0 halt code = 5 HALT instruction executed PC = 1d5e8 boot failure Images Affected: [SYS$LDR]SYS$DQDRIVER.EXE o When mounting an ATAPI device an ATA init_device_param command attempts to set the disk geometry. This command is illegal for ATAPI devices but it takes 15 seconds before the drive reports the error. Images Affected: [SYS$LDR]SYS$DQDRIVER.EXE INSTALLATION NOTES: This kit requires a system reboot. Compaq strongly recommends that a reboot is performed immediately after kit installation to avoid system instability If you have other nodes in your OpenVMS cluster, they must also be rebooted in order to make use of the new image(s). If it is not possible or convenient to reboot the entire cluster at this time, a rolling re-boot may be performed. INSTALLATION INSTRUCTIONS: Install this kit with the POLYCENTER Software installation utility by logging into the SYSTEM account, and typing the following at the DCL prompt: PRODUCT INSTALL VMS73_DRIVER /SOURCE=[location of Kit] The kit location may be a tape drive, CD, or a disk directory that contains the kit. Additional help on installing PCSI kits can be found by typing HELP PRODUCT INSTALL at the system prompt Special Installation Instructions: o Scripting of Answers to Installation Questions During installation, this kit will ask and require user response to several questions. If you wish to automate the installation of this kit and avoid having to provide responses to these questions, you must create a DCL command procedure that includes the following definitions and commands: - $ DEFINE/SYS NO_ASK$BACKUP TRUE - $ DEFINE/SYS NO_ASK$REBOOT TRUE - Add the following qualifiers to the PRODUCT INSTALL command and add that command to the DCL procedure. /PROD=DEC/BASE=AXPVMS/VER=V2.0 - De-assign the logicals assigned For example, a sample command file to install the VMS73_DRIVER-V0200 kit would be: $ $ DEFINE/SYS NO_ASK$BACKUP TRUE $ DEFINE/SYS NO_ASK$REBOOT TRUE $! $ PROD INSTALL VMS73_DRIVE/PROD=DEC/BASE=AXPVMS/VER=V2.0 $! $ DEASSIGN/SYS NO_ASK$BACKUP $ DEASSIGN/SYS NO_ASK$REBOOT $! $ exit All trademarks are the property of their respective owners.



Files on this server are as follows:

dec-axpvms-vms73_driver-v0200--4.README
dec-axpvms-vms73_driver-v0200--4.CHKSUM
dec-axpvms-vms73_driver-v0200--4.pcsi-dcx_axpexe
vms73_driver-v0200.CVRLET_TXT

privacy and legal statement